{
  "schema_version": "2.0",
  "run_id": "assembly-seed202",
  "backend": "Isaac Lab PhysX on bimanual YAM",
  "simulation_task_passed": true,
  "production_ready": false,
  "production_blockers": [
    "Physical hardware validation is not performed",
    "Contact readings are sampled at the control rate. Substep peak coverage is not certified",
    "Independent wrist sensor calibration and safety validation are outstanding"
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  },
  "blockers": [],
  "metrics": {
    "samples": 2064,
    "duration_s": 103.14999999999628,
    "final_gap_mm": -0.00010640360414981842,
    "final_yaw_error_deg": 0.13052961230278015,
    "final_lateral_error_mm": 0.7858585715293884,
    "final_relative_position_mm": [
      0.7596356444992125,
      0.20131403289269656,
      -1.0001064511016011
    ],
    "final_pin_position_mm": [
      -0.04483207521843724,
      -0.03429450953262858,
      4.000961780548096
    ],
    "peak_sampled_axial_n": 28.76677567110859,
    "peak_sampled_lateral_n": 7.49146929972126,
    "peak_sampled_torque_nm": 0.4193147830756278,
    "longest_pull_duration_s": 2.0499999999998835,
    "observed_motion_deg": 30.071603775024414
  },
  "telemetry_sha256": "f34b6b2ab8d4fe03f03e2046696fdc8f16abadcea29db252fb1f29037964909c",
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.000000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.000000000000107,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.000000000000163,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 27.20000000000025,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 34.350000000000186,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 36.40000000000007,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 48.64999999999937,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 54.99999999999901,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 73.64999999999796,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 75.69999999999784,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 82.44999999999746,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 94.49999999999677,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 97.34999999999661,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 99.3999999999965,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ]
}