{
  "schema_version": "2.0",
  "run_id": "assembly-seed204",
  "backend": "Isaac Lab PhysX on bimanual YAM",
  "simulation_task_passed": true,
  "production_ready": false,
  "production_blockers": [
    "Physical hardware validation is not performed",
    "Contact readings are sampled at the control rate. Substep peak coverage is not certified",
    "Independent wrist sensor calibration and safety validation are outstanding"
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  },
  "blockers": [],
  "metrics": {
    "samples": 2119,
    "duration_s": 105.89999999999613,
    "final_gap_mm": -0.00010756775736808777,
    "final_yaw_error_deg": 0.22973772883415222,
    "final_lateral_error_mm": 2.66731333732605,
    "final_relative_position_mm": [
      -0.6916176062077284,
      2.5760873686522245,
      -1.0001076152548194
    ],
    "final_pin_position_mm": [
      -0.6063992041163146,
      1.1426041601225734,
      4.004477988928556
    ],
    "peak_sampled_axial_n": 37.43447505709603,
    "peak_sampled_lateral_n": 9.782262478886391,
    "peak_sampled_torque_nm": 0.378391638679827,
    "longest_pull_duration_s": 2.0499999999998835,
    "observed_motion_deg": 30.07174301147461
  },
  "telemetry_sha256": "249bdaf1655dca8545e5594e10b205b57eef56306ec155a90491d5bbf9fe25da",
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.000000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.000000000000234,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.00000000000029,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.00000000000032,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 39.3499999999999,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 41.399999999999785,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 53.64999999999909,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 57.34999999999888,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 74.29999999999792,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 76.3499999999978,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 83.09999999999742,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 97.24999999999662,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 100.09999999999646,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 102.14999999999634,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ]
}