{
  "schema_version": "2.0",
  "run_id": "assembly-seed342",
  "backend": "Isaac Lab PhysX on bimanual YAM",
  "simulation_task_passed": true,
  "production_ready": false,
  "production_blockers": [
    "Physical hardware validation is not performed",
    "Contact readings are sampled at the control rate. Substep peak coverage is not certified",
    "Independent wrist sensor calibration and safety validation are outstanding"
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  },
  "blockers": [],
  "metrics": {
    "samples": 2141,
    "duration_s": 106.99999999999606,
    "final_gap_mm": -0.00016670674085617065,
    "final_yaw_error_deg": 0.25726044178009033,
    "final_lateral_error_mm": 2.735198974609375,
    "final_relative_position_mm": [
      1.9640426617115736,
      1.9036412704735994,
      -1.0001667542383075
    ],
    "final_pin_position_mm": [
      0.99893135484308,
      -0.009217665137839504,
      4.001021385192871
    ],
    "peak_sampled_axial_n": 29.73112793603152,
    "peak_sampled_lateral_n": 7.589042083832333,
    "peak_sampled_torque_nm": 0.24133866670436055,
    "longest_pull_duration_s": 2.0499999999998835,
    "observed_motion_deg": 30.07201385498047
  },
  "telemetry_sha256": "2593ef73cfcfe1d5dcd2442459430d11650d8a500e26de8c8c3d4d95417d5e3c",
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 13.00000000000005,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 27.00000000000025,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 31.000000000000306,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 33.300000000000246,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 40.39999999999984,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 42.449999999999726,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 54.69999999999903,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 58.7499999999988,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 77.69999999999773,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 79.74999999999761,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 86.49999999999723,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 98.34999999999656,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 101.1999999999964,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 103.24999999999628,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ]
}