{
  "schema_version": "2.0",
  "run_id": "assembly-seed343",
  "backend": "Isaac Lab PhysX on bimanual YAM",
  "simulation_task_passed": true,
  "production_ready": false,
  "production_blockers": [
    "Physical hardware validation is not performed",
    "Contact readings are sampled at the control rate. Substep peak coverage is not certified",
    "Independent wrist sensor calibration and safety validation are outstanding"
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  },
  "blockers": [],
  "metrics": {
    "samples": 2134,
    "duration_s": 106.64999999999608,
    "final_gap_mm": -0.0001671724021434784,
    "final_yaw_error_deg": 0.3212352395057678,
    "final_lateral_error_mm": 5.6586222648620605,
    "final_relative_position_mm": [
      0.3899898147210479,
      5.645167548209429,
      -1.0001672198995948
    ],
    "final_pin_position_mm": [
      -0.13235957885626704,
      0.9151070844382048,
      4.003762733191252
    ],
    "peak_sampled_axial_n": 30.23838355903485,
    "peak_sampled_lateral_n": 7.113207324309486,
    "peak_sampled_torque_nm": 0.23252243528529912,
    "longest_pull_duration_s": 2.0499999999998835,
    "observed_motion_deg": 30.0718936920166
  },
  "telemetry_sha256": "954766a32f62449bfd85ef040e35096eae2ba2f6f7a812629a4268cb76239013",
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.250000000000039,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.250000000000238,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.250000000000295,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.250000000000306,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 39.24999999999991,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 41.29999999999979,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 53.549999999999095,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 58.84999999999879,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 77.29999999999775,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 79.34999999999764,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 86.09999999999725,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 97.99999999999658,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 100.84999999999641,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 102.8999999999963,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ]
}