{
  "schema_version": "2.0",
  "run_id": "assembly-seed344",
  "backend": "Isaac Lab PhysX on bimanual YAM",
  "simulation_task_passed": true,
  "production_ready": false,
  "production_blockers": [
    "Physical hardware validation is not performed",
    "Contact readings are sampled at the control rate. Substep peak coverage is not certified",
    "Independent wrist sensor calibration and safety validation are outstanding"
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  },
  "blockers": [],
  "metrics": {
    "samples": 2188,
    "duration_s": 109.34999999999593,
    "final_gap_mm": -0.0001701992005109787,
    "final_yaw_error_deg": 0.16461396217346191,
    "final_lateral_error_mm": 7.01629638671875,
    "final_relative_position_mm": [
      -0.8036367944441736,
      6.970121059566736,
      -1.0001702466979623
    ],
    "final_pin_position_mm": [
      -0.39465256850235164,
      0.024743236281210557,
      4.001200199127197
    ],
    "peak_sampled_axial_n": 37.734648521299334,
    "peak_sampled_lateral_n": 7.843344638541369,
    "peak_sampled_torque_nm": 0.30385196417440263,
    "longest_pull_duration_s": 2.0499999999998835,
    "observed_motion_deg": 30.071794509887695
  },
  "telemetry_sha256": "11c3ceb95e76219c94d865f9777c30a3abe25b7703db73a27ab5fa1399048607",
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.100000000000037,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.100000000000108,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.100000000000165,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 27.75000000000026,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 34.80000000000016,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 36.850000000000044,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 49.09999999999935,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 54.049999999999066,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 72.44999999999803,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 74.49999999999791,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 81.24999999999753,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 100.69999999999642,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 103.54999999999626,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 105.59999999999614,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ]
}