{
  "schema_version": "2.0",
  "run_id": "assembly-seed400",
  "backend": "Isaac Lab PhysX on bimanual YAM",
  "simulation_task_passed": true,
  "production_ready": false,
  "production_blockers": [
    "Physical hardware validation is not performed",
    "Contact readings are sampled at the control rate. Substep peak coverage is not certified",
    "Independent wrist sensor calibration and safety validation are outstanding"
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  },
  "blockers": [],
  "metrics": {
    "samples": 2074,
    "duration_s": 103.64999999999625,
    "final_gap_mm": -0.0001069856807589531,
    "final_yaw_error_deg": 0.2937568426132202,
    "final_lateral_error_mm": 2.155163049697876,
    "final_relative_position_mm": [
      1.6332876402884722,
      1.4060934772714972,
      -1.0001070331782103
    ],
    "final_pin_position_mm": [
      0.7225705194287002,
      0.5058348178863525,
      4.002511501312256
    ],
    "peak_sampled_axial_n": 30.080057454496487,
    "peak_sampled_lateral_n": 7.360673520712163,
    "peak_sampled_torque_nm": 0.23921834453293173,
    "longest_pull_duration_s": 2.0499999999998835,
    "observed_motion_deg": 30.07173728942871
  },
  "telemetry_sha256": "6c09efcaf87f5d251650a6e91cbb4173b791625b93a96b8f3012cd406ae1cd72",
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.200000000000038,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.200000000000237,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.200000000000294,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.20000000000031,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 38.79999999999993,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 40.84999999999982,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 53.09999999999912,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 57.84999999999885,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 74.54999999999791,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 76.59999999999779,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 83.34999999999741,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 94.99999999999675,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 97.84999999999658,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 99.89999999999647,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ]
}