{
  "schema_version": "2.0",
  "run_id": "cli-alignment345-v20",
  "backend": "Isaac Lab PhysX on bimanual YAM",
  "simulation_task_passed": true,
  "production_ready": false,
  "production_blockers": [
    "Physical hardware validation is not performed",
    "Contact readings are sampled at the control rate. Substep peak coverage is not certified",
    "Independent wrist sensor calibration and safety validation are outstanding"
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  },
  "blockers": [],
  "metrics": {
    "samples": 2080,
    "duration_s": 103.94999999999624,
    "final_gap_mm": -0.00010652001947164536,
    "final_yaw_error_deg": 0.2937268912792206,
    "final_lateral_error_mm": 2.1589901447296143,
    "final_relative_position_mm": [
      -0.007058309620333603,
      2.1589784882962704,
      -1.000106567516923
    ],
    "final_pin_position_mm": [
      -0.7254787487909198,
      1.1342946672812104,
      4.004418849945068
    ],
    "peak_sampled_axial_n": 29.921384100198523,
    "peak_sampled_lateral_n": 8.055021065839146,
    "peak_sampled_torque_nm": 0.3605477313968732,
    "longest_pull_duration_s": 2.0499999999998835,
    "observed_motion_deg": 30.071866989135742
  },
  "telemetry_sha256": "c58f904865f59b10ed402565af48a4d09e4d76fa432474943f61cff7a61f1aa1",
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.150000000000038,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.150000000000237,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.150000000000293,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.3000000000003,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 38.79999999999993,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 40.84999999999982,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 53.09999999999912,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 56.84999999999891,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 73.74999999999795,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 75.79999999999784,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 82.54999999999745,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 95.29999999999673,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 98.14999999999657,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 100.19999999999645,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ]
}