{
  "schema_version": "2.0",
  "run_id": "cli-alignment348-v20",
  "backend": "Isaac Lab PhysX on bimanual YAM",
  "simulation_task_passed": true,
  "production_ready": false,
  "production_blockers": [
    "Physical hardware validation is not performed",
    "Contact readings are sampled at the control rate. Substep peak coverage is not certified",
    "Independent wrist sensor calibration and safety validation are outstanding"
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  },
  "blockers": [],
  "metrics": {
    "samples": 2069,
    "duration_s": 103.39999999999627,
    "final_gap_mm": -0.00016624107956886292,
    "final_yaw_error_deg": 0.22080744802951813,
    "final_lateral_error_mm": 7.094691753387451,
    "final_relative_position_mm": [
      -1.376832602545619,
      6.9598122499883175,
      -1.0001662885770202
    ],
    "final_pin_position_mm": [
      -0.739638227969408,
      0.053651318012271076,
      4.001259803771973
    ],
    "peak_sampled_axial_n": 34.24535233741521,
    "peak_sampled_lateral_n": 7.560313476785986,
    "peak_sampled_torque_nm": 0.48536443608959007,
    "longest_pull_duration_s": 2.0499999999998835,
    "observed_motion_deg": 30.071828842163086
  },
  "telemetry_sha256": "3cc6660af03b5428c0236f515169f99a22fb1b7903d2c363eb06e069f29306f1",
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.000000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.000000000000107,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.000000000000163,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 23.050000000000193,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 29.80000000000029,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 31.800000000000317,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 44.049999999999635,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 50.24999999999928,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 69.09999999999822,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 71.1499999999981,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 77.89999999999772,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 94.74999999999676,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 97.5999999999966,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 99.64999999999648,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ]
}