{
  "schema_version": "2.0",
  "run_id": "cli-grasp-v17",
  "backend": "Isaac Lab PhysX on bimanual YAM",
  "simulation_task_passed": false,
  "production_ready": false,
  "production_blockers": [
    "Physical hardware validation is not performed",
    "Contact readings are sampled at the control rate. Substep peak coverage is not certified",
    "Independent wrist sensor calibration and safety validation are outstanding"
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": false,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  },
  "blockers": [
    "seating"
  ],
  "metrics": {
    "samples": 2068,
    "duration_s": 103.34999999999627,
    "final_gap_mm": -0.00016624107956886292,
    "final_yaw_error_deg": 7.1262359619140625,
    "final_lateral_error_mm": 0.9036723375320435,
    "final_relative_position_mm": [
      -0.21164555801078677,
      0.8785384707152843,
      -1.0001662885770202
    ],
    "final_pin_position_mm": [
      -0.2844794071279466,
      0.1345274067716673,
      4.001379013061523
    ],
    "peak_sampled_axial_n": 28.428420201040943,
    "peak_sampled_lateral_n": 5.4735718959479245,
    "peak_sampled_torque_nm": 0.6328307512080591,
    "longest_pull_duration_s": 2.0499999999998835,
    "observed_motion_deg": 30.071931838989258
  },
  "telemetry_sha256": "0f876eb66327277dd3b4d2cfced3077f960cfa32bbea1dd18bdd53f1aa0c7487",
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.050000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.050000000000107,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.050000000000164,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 26.000000000000234,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 33.20000000000025,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 35.250000000000135,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 47.49999999999944,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 54.49999999999904,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 72.849999999998,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 74.89999999999789,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 81.6499999999975,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 94.69999999999676,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 97.5499999999966,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 99.59999999999648,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ]
}