{
  "schema_version": "2.0",
  "run_id": "cli-grasp-v18",
  "backend": "Isaac Lab PhysX on bimanual YAM",
  "simulation_task_passed": true,
  "production_ready": false,
  "production_blockers": [
    "Physical hardware validation is not performed",
    "Contact readings are sampled at the control rate. Substep peak coverage is not certified",
    "Independent wrist sensor calibration and safety validation are outstanding"
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  },
  "blockers": [],
  "metrics": {
    "samples": 2106,
    "duration_s": 105.24999999999616,
    "final_gap_mm": -0.00016938429325819016,
    "final_yaw_error_deg": 0.32338497042655945,
    "final_lateral_error_mm": 6.159235954284668,
    "final_relative_position_mm": [
      0.8575150277465582,
      6.099250633269548,
      -1.0001694317907095
    ],
    "final_pin_position_mm": [
      0.0769410835346207,
      0.2349676942685619,
      4.001855850219727
    ],
    "peak_sampled_axial_n": 28.561938254541722,
    "peak_sampled_lateral_n": 8.193360677484979,
    "peak_sampled_torque_nm": 0.243889583529156,
    "longest_pull_duration_s": 2.0499999999998835,
    "observed_motion_deg": 30.07177734375
  },
  "telemetry_sha256": "9eaa5c4134b62949aace929a23fe82651b3648407cac62643fb49b4646bf5831",
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.050000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.050000000000107,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.050000000000164,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 26.000000000000234,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 33.20000000000025,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 35.250000000000135,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 47.49999999999944,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 54.49999999999904,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 72.849999999998,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 74.89999999999789,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 81.6499999999975,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 96.59999999999665,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 99.44999999999649,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 101.49999999999638,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ]
}