{
  "schema_version": "2.0",
  "run_id": "cli-grasp401-v21",
  "backend": "Isaac Lab PhysX on bimanual YAM",
  "simulation_task_passed": false,
  "production_ready": false,
  "production_blockers": [
    "Physical hardware validation is not performed",
    "Contact readings are sampled at the control rate. Substep peak coverage is not certified",
    "Independent wrist sensor calibration and safety validation are outstanding"
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": false,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  },
  "blockers": [
    "seating"
  ],
  "metrics": {
    "samples": 2111,
    "duration_s": 105.49999999999615,
    "final_gap_mm": -0.00010605435818433762,
    "final_yaw_error_deg": 7.35785436630249,
    "final_lateral_error_mm": 0.8625043630599976,
    "final_relative_position_mm": [
      -0.1663984585320577,
      -0.8463009726256132,
      -1.0001061018556356
    ],
    "final_pin_position_mm": [
      -0.17110192857217044,
      1.1282837949693203,
      4.004418384283781
    ],
    "peak_sampled_axial_n": 32.13446162016602,
    "peak_sampled_lateral_n": 5.747748705326343,
    "peak_sampled_torque_nm": 0.7871233601840495,
    "longest_pull_duration_s": 2.0499999999998835,
    "observed_motion_deg": 30.071853637695312
  },
  "telemetry_sha256": "4c7778901ebada020f55f96260a37ef36dd0087e8f1d4910b4210dbebc8f7d4c",
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.000000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.000000000000234,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.00000000000029,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.65000000000028,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 39.14999999999991,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 41.1999999999998,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 53.4499999999991,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 56.9499999999989,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 73.59999999999796,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 75.64999999999785,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 82.39999999999746,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 96.19999999999668,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 99.04999999999652,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 101.0999999999964,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ]
}