MJAK Labs / Manufacturing research / Recorded evidence
Bimanual YAM / Isaac Lab Arena

Autonomous humanoid gripper installation and verification

This report is presenting recorded evidence as of 17 November 2026 at 14:12 IST.

Assembly sequence passedHardware production release remains closed
3 / 4Full accepted trials with the current controller
15Recorded public dataset evaluations
23Recorded runs passing every implemented simulation task check

Purpose and scope

Two YAM arms are installing a replaceable gripper module into a humanoid wrist housing. The left arm is stabilizing the housing while the right arm is aligning the module and inserting a retaining pin through physical cross holes. The verification sequence is applying a sustained pull load and exercising both gripper jaws before release.

The deterministic controller is responding to measured simulator poses and contact forces. Separate inspection and process monitoring models are being evaluated on three public datasets.

GPU simulation acceptance

The recorded CLI recovery is completing the entire installation sequence. It is detecting a physical insertion bind and recovering through retraction and realignment. It is inserting the retaining pin before applying the pull proof. It is opening and closing both gripper jaws before releasing both arms.

Independent measurementRecorded result
Accepted runcli-alignment345-v20
Continuous qualifying pull2.05 seconds
Peak sampled axial force29.92 N against a 45 N limit
Peak sampled lateral force8.06 N against a 12 N limit
Peak sampled interface torque0.361 Nm against a 2.5 Nm limit
Observed motion of both jaws30.07 degrees
Final keyed orientation error0.294 degrees against a 1 degree limit
Final transverse positionX -0.007 mm and Y 2.159 mm. Modeled limits are 2 mm in X and 7 mm in Y.
Final simulated gap-0.000107 mm
Both arms releasedMeasured open grippers and tool clearance

The very small negative gap is representing numerical contact penetration in the simulated geometry. It is not establishing hardware metrology accuracy. Independent JSON acceptance record

Measured grasp stabilization

The postprocessing audit is measuring a maximum relative tool translation of 1.696 mm within the grasped object frame. This is passing the unchanged 2 mm gate. This proxy is including relative compliance and is not directly measuring contact patch slip.

ArmObjectGrasp start secondsGrasp end secondsPeak relative translation mm
rightmodule5.0541.451.696
rightpin47.1076.400.359
rightmodule82.0595.901.480
lefthousing5.05101.250.802

Grasp audit JSON. Passing the implemented assembly sequence is not satisfying every broader production requirement.

Current release gates

The release checker is finding 3 fully accepted trials in 4 rendered trials with matching controller and safety guard hashes. Full campaign acceptance is requiring the assembly sequence and the 2 mm grasp proxy plus successful evidence export in each counted pass.

GateObserved status
Grasp motion proxy availablePASS
Grasp motion proxy within 2mmPASS
At least 20 full trialsBLOCKED
Full trial success rate at least 95 percentBLOCKED
Campaign evidence completePASS
Campaign has no grasp limit violationsBLOCKED
Campaign has no sampled safety violationsPASS
Calibrated hardware wrenchBLOCKED
Physics substep peak coverageBLOCKED
Physical hardware validationBLOCKED

Simulation campaign readiness is reporting false. Hardware production readiness is reporting false. Current release JSON

Complete campaign with grasp and video gates

Each row is preserving its recorded outcome. The acceptance decision is requiring successful process completion and all assembly checks plus a grasp motion proxy no greater than 2 mm. It is also requiring successful export of all camera videos. Failed trials are remaining in the denominator.

SeedFrozen controllerAssemblyGrasp proxy mmFull acceptanceRecorded evidence
340cli-regression205-v19PASS1.794PASSJSON
341cli-regression205-v19PASS1.509PASSJSON
342cli-regression205-v19PASS1.939PASSJSON
343cli-regression205-v19PASS1.447PASSJSON
344cli-regression205-v19PASS1.607PASSJSON
345cli-regression205-v19FAIL1.696FAILJSON
346cli-regression205-v19PASS1.604PASSJSON
347cli-regression205-v19PASS1.696PASSJSON
348cli-regression205-v19FAIL1.559FAILJSON
400cli-alignment345-v20PASS1.601PASSJSON
401cli-alignment345-v20PASS2.023FAILJSON
402cli-alignment345-v20PASS1.464PASSJSON
403cli-alignment345-v20PASS1.429PASSJSON

Reliability is being evaluated by revision

The table is separating controller revisions and rendering configurations. It is identifying the acceptance gate used for each campaign. It is counting timeouts as unsuccessful attempts. It is not pooling development failures into a claimed final controller success rate. The interval is using the Wilson method. Small trial counts are leaving substantial uncertainty.

Frozen controllerExecution modeAcceptance scopeAttemptsPassesObserved rate95 percent interval
cli-recovery-v11Rendering enabledLegacy assembly sequence only200.0%0.000 to 0.658
cli-retry-v13Rendering enabledLegacy assembly sequence only4375.0%0.301 to 0.954
cli-retry-v13Physics only experimental wrapperLegacy assembly sequence only11100.0%0.207 to 1.000
cli-regression205-v19Rendering enabledAssembly plus grasp and video9777.8%0.453 to 0.937
cli-alignment345-v20Rendering enabledAssembly plus grasp and video4375.0%0.301 to 0.954

Campaign retirement decisions

These campaigns are stopping early after recorded failures make the declared acceptance target unreachable. Unrun trials are not being counted as successes. Subsequent controller revisions are requiring separate qualification.

CampaignPlanned TrialsCompleted TrialsFull PassesFailed SeedsRecord
campaign-retirement-4002043[401]JSON
campaign-retirement-3402097[345, 348]JSON

Execution continuity

The campaign is retaining interrupted recordings separately from completed trials. The continuation is validating the original randomization design and source hashes before repeating the interrupted seeds. Completed failures are remaining in the acceptance denominator.

Archived Attempt GroupInterrupted SeedsRecord
v22-paused-1794904381375389485cli-grasp401-v22, cli-grasp345-v22, cli-grasp348-v22, cli-grasp205-v22JSON record
campaign-400-retired-1794901734179431126assembly-seed404, assembly-seed405, assembly-seed406, assembly-seed407JSON record
campaign-340-1794894855072026408assembly-seed342, assembly-seed343JSON record
campaign-340-retired-1794898054381892427assembly-seed349, assembly-seed350JSON record

Complete assembly campaign

The CLI is running a separate campaign against frozen source from the complete assembly controller. The table is including recorded attempts with independent records. It is reporting 15 accepted assemblies in 20 recorded attempts across controller revisions. The earlier twenty insertion trials are using the earlier fixture revision and are not contributing to this count.

SeedFrozen source runYaw degreesFriction scaleMass scalePull secondsComplete gateUnmet checks
200cli-recovery-v11-5.450.881.040.000FAILcomplete_assembly_sequence, sustained_pull, observed_motion, arms_released
201cli-recovery-v11-4.291.140.950.000FAILsampled_force_limits, sustained_pull, observed_motion, arms_released
202cli-retry-v133.171.060.982.050PASS
203cli-retry-v13-3.621.071.092.050PASS
204cli-retry-v13-0.871.140.912.050PASS
205cli-retry-v130.330.881.000.000FAILcomplete_assembly_sequence, pin_engagement, sampled_force_limits, sustained_pull, observed_motion, arms_released
206cli-retry-v13-5.900.921.052.050PASS
340cli-regression205-v19-1.200.841.012.050PASS
341cli-regression205-v193.600.850.962.050PASS
342cli-regression205-v19-2.241.081.102.050PASS
343cli-regression205-v19-2.940.861.092.050PASS
344cli-regression205-v193.710.911.012.050PASS
345cli-regression205-v19-5.580.821.000.000FAILcomplete_assembly_sequence, seating, pin_engagement, sustained_pull, observed_motion, arms_released
346cli-regression205-v19-4.400.901.002.050PASS
347cli-regression205-v19-2.380.860.992.050PASS
348cli-regression205-v191.860.861.010.000FAILcomplete_assembly_sequence, seating, pin_engagement, sustained_pull, observed_motion, arms_released
400cli-alignment345-v20-2.310.901.062.050PASS
401cli-alignment345-v200.791.110.992.050PASS
402cli-alignment345-v205.231.141.012.050PASS
403cli-alignment345-v205.320.910.942.050PASS

Every phase is carrying an evidence requirement

PhaseRequired behaviorCurrent evidence boundary
Mechanical assetsPhysical housing walls and keyed shaft. Separate cross pin. Articulated gripper jaws.The scene is generating collision geometry and rigid body dynamics.
Bimanual coordinationLeft fixture stabilization and right component transportThe recordings and joint logs are showing both YAM arms acting in one scene.
Precision insertion32 mm target depth and 0.8 mm maximum interface gapThe independent scorer is reading relative poses. It is retaining small negative contact penetration values rather than clipping them.
Failure detectionLoaded insertion with insufficient progress. Sensor errors. Timeouts.The controller is recording the measurement and selected bounded transition.
RecoveryUnload and retract. Realign using measured poses. Retry within a fixed budget.The report is retaining failed development attempts. The complete campaign table is reporting coverage by frozen controller.
Mechanical retentionA real pin is passing through physical holesThe verifier is checking position and subsequent loaded retention rather than a scripted lock flag.
Pull proof25 N for two uninterrupted secondsThe verifier is recomputing the longest qualifying interval from recorded samples.
Motion proof30 degree opening and observed return of both gripper jawsThe scorer is reading articulation joint coordinates rather than accepting actuator commands as completion.
Safe releaseBoth grippers open and both tools retreatThe scorer is checking measured opening and clearance.
CLI and evidenceValidate. Run. Diagnose. Retry. Verify. Report. Public QA execution.The project is storing source snapshots and hashes with named runs.
Repeatability20 complete randomized assembly trialsThe current release table is tracking the matching controller campaign. Earlier insertion trials are being reported separately.
Learned manipulationOptional research extensionNo VLA rollout or learned manipulation success is being claimed in this session.

Public data is testing the reusable QA components

The image experiments are fitting a normal feature memory using a frozen ImageNet ResNet18 encoder. Patch distances are producing anomaly scores. The robot process experiment is training a GPU autoencoder on cycle summaries. Its inputs are including the mean and standard deviation plus the fifth and ninety fifth percentiles of 130 robot signals.

Each run is separating normal fitting data from normal calibration data. The calibration set is setting the threshold at its ninety ninth score percentile before test scoring. Test labels are entering metric computation only. The voraus split is keeping complete sample IDs together. It is a custom split and is not reproducing the published MVT Flow protocol. Its cycle summary is not preserving temporal order.

The bootstrap interval is using 500 test sample resamples. It is describing uncertainty under this sample assumption. It is not proving independence between related production settings. Repeated seeds are revealing split and initialization sensitivity. High AUROC is not removing false negatives at the chosen threshold.

DatasetSeedFitCalibrationTestAUROC95 percent intervalRecallMissed anomaliesFalse alarmsEvidence
ksdd242166841710040.9260.892 to 0.9550.682357Predictions
ksdd243166841710040.9320.901 to 0.9570.673364Predictions
ksdd244166841710040.9280.894 to 0.9570.7003314Predictions
ksdd245166841710040.9310.902 to 0.9570.673367Predictions
ksdd246166841710040.9360.909 to 0.9600.664377Predictions
mvtec-metal-nut42176441150.9730.944 to 0.9930.92571Predictions
mvtec-metal-nut43176441150.9730.942 to 0.9950.90391Predictions
mvtec-metal-nut44176441150.9740.941 to 0.9960.90391Predictions
mvtec-metal-nut45176441150.9770.950 to 0.9960.93562Predictions
mvtec-metal-nut46176441150.9770.949 to 0.9960.92571Predictions
voraus-ad4282027310290.9910.985 to 0.9960.6942313Predictions
voraus-ad4382027310290.9800.969 to 0.9900.4863883Predictions
voraus-ad4482027310290.9870.979 to 0.9940.6682513Predictions
voraus-ad4582027310290.9890.981 to 0.9950.6082962Predictions
voraus-ad4682027310290.9900.982 to 0.9950.7342013Predictions

MVTec AD Metal Nut

ROC and score distributions
Real dataset examples and anomaly maps
Full measured metrics
{
  "dataset": "mvtec-metal-nut",
  "test_samples": 115,
  "normal": 22,
  "anomalous": 93,
  "auroc": 0.9726295210166177,
  "average_precision": 0.9938472942375032,
  "auroc_ci95": [
    0.9443124685771744,
    0.9933816722205631
  ],
  "threshold": 1.4768710505962372,
  "threshold_rule": "99th percentile of held out normal calibration scores",
  "precision": 0.9885057471264368,
  "recall": 0.9247311827956989,
  "specificity": 0.9545454545454546,
  "false_negatives": 7,
  "false_positives": 1,
  "true_positives": 86,
  "true_negatives": 21,
  "gpu": "NVIDIA L40S",
  "peak_gpu_memory_mb": 221.1875,
  "seed": 42,
  "scope": "Public proxy QA evaluation. This is not assembly verification.",
  "method": "ResNet18 ImageNet frozen layer3 patch nearest neighbour baseline",
  "train_samples": 176,
  "calibration_samples": 44,
  "memory_patches": 16000,
  "input_resolution": [
    256,
    256
  ],
  "wall_seconds": 6.134582757949829,
  "inference_ms_per_image": 13.647694739130083,
  "latency_scope": "Image loading preprocessing GPU inference and nearest neighbour search under concurrent workload. Not isolated latency.",
  "prediction_sha256": "9a6996a2f32106d44ea13ecb17201394bfcac028153e942057ac2818fbbd498f"
}

KolektorSDD2

ROC and score distributions
Real dataset examples and anomaly maps
Full measured metrics
{
  "dataset": "ksdd2",
  "test_samples": 1004,
  "normal": 894,
  "anomalous": 110,
  "auroc": 0.9261134838316047,
  "average_precision": 0.8205660747101688,
  "auroc_ci95": [
    0.8915219185366684,
    0.9554166016593534
  ],
  "threshold": 1.2162013530731195,
  "threshold_rule": "99th percentile of held out normal calibration scores",
  "precision": 0.9146341463414634,
  "recall": 0.6818181818181818,
  "specificity": 0.9921700223713646,
  "false_negatives": 35,
  "false_positives": 7,
  "true_positives": 75,
  "true_negatives": 887,
  "gpu": "NVIDIA L40S",
  "peak_gpu_memory_mb": 218.0859375,
  "seed": 42,
  "scope": "Public proxy QA evaluation. This is not assembly verification.",
  "method": "ResNet18 ImageNet frozen layer3 patch nearest neighbour baseline",
  "train_samples": 1668,
  "calibration_samples": 417,
  "memory_patches": 16000,
  "input_resolution": [
    256,
    256
  ],
  "wall_seconds": 15.814876317977905,
  "inference_ms_per_image": 4.585953388446213,
  "latency_scope": "Image loading preprocessing GPU inference and nearest neighbour search under concurrent workload. Not isolated latency.",
  "prediction_sha256": "d3fcb41d6cce63664de079ad2dbfdb3355159dd76ec1391c4f51c7dd50abdd99"
}

Voraus AD

ROC and score distributions
Full measured metrics
{
  "dataset": "voraus-ad",
  "test_samples": 1029,
  "normal": 274,
  "anomalous": 755,
  "auroc": 0.991429400106347,
  "average_precision": 0.9963537089423591,
  "auroc_ci95": [
    0.9853441632694844,
    0.9963725552451105
  ],
  "threshold": 0.3419836759567261,
  "threshold_rule": "99th percentile of held out normal calibration scores",
  "precision": 0.9943074003795066,
  "recall": 0.6940397350993377,
  "specificity": 0.9890510948905109,
  "false_negatives": 231,
  "false_positives": 3,
  "true_positives": 524,
  "true_negatives": 271,
  "gpu": "NVIDIA L40S",
  "peak_gpu_memory_mb": 39.88916015625,
  "seed": 42,
  "scope": "Public proxy QA evaluation. This is not assembly verification.",
  "method": "Normal only GPU autoencoder on per cycle mean standard deviation and 5th and 95th signal percentiles",
  "train_samples": 820,
  "calibration_samples": 273,
  "signal_count": 130,
  "feature_count": 520,
  "wall_seconds": 9.356644630432129,
  "split_protocol": "Custom seeded split by complete sample ID. No rows from a cycle cross splits. Not the published MVT Flow protocol.",
  "limitations": "Cycle summary features do not preserve temporal ordering. Test samples may share settings. No claim of unseen setting generalization.",
  "prediction_sha256": "674d4bebf02b96039be18c7352dc9af4fe0f2c3e8c4c4a9d198a624965333752"
}

The CLI is operating the workflow

The command line is launching simulation and model evaluation. It is refusing to overwrite existing named evidence. The physical verifier is recomputing acceptance from telemetry. Automatic retry is being restricted to an insertion failure. A failed pull proof is requiring mechanical diagnosis rather than automatic approval.

humanoid-cell validate workorders/gripper_install.json
humanoid-cell run workorders/gripper_install.json --policy nominal --record failure
humanoid-cell diagnose session/runs/failure
humanoid-cell retry session/runs/failure --recovery auto --record recovery
humanoid-cell verify session/runs/recovery
humanoid-cell report session/runs/recovery/assembly_record.json --output assembly-certificate.html
humanoid-cell qa-run all --seed 46 --parallel 3
humanoid-cell evaluate-isaac --source-run cli-alignment345-v20 --trials 20 --start-seed 400 --parallel 4

The session is preserving the actual CLI execution status in the public dataset job record. It is preserving test output in the current software test log. Named examples above are documenting the workflow. The run table is identifying the recordings that actually exist.

CLI verification

The regression suite is checking work order validation and bounded recovery decisions. It is also checking evidence integrity and campaign continuation behavior.

........................................................................ [100%]
72 passed in 0.14s

Complete software test log

Experimental configuration

ComponentRecorded Configuration
GPUNVIDIA L40S with 46068 MiB reported memory
RuntimeIsaac Lab Arena with PhysX and Inspect Robots
EmbodimentTwo YAM arms with official joint and actuator effort limits
Physics and control240 Hz physics and 20 Hz control observations
ControllerDeterministic pose feedback with bounded phase transitions and measured force feedback
SensingSimulator poses and interface contact views
FixtureFour kilogram base with table support and active left arm stabilization

GPU campaign resource measurements

The monitor is sampling the actual GPU and available disk space every ten seconds during continued validation. Startup and video export are remaining in the sampling window.

MeasurementMinimumMeanMaximum
utilization_percent0.082.299.0
memory_used_mib1.015012.821155.0
power_w22.3100.6122.3
temperature_c28.041.446.0
free_disk_gib0.75.67.9

The window is including 922 samples from 2026-11-17T05:56:36.675033+00:00 to 2026-11-17T08:30:32.304340+00:00. Campaign resource JSON log

Resource measurements

The values are describing the recorded sampling window while the full assembly and controller probe are running. They are not estimating utilization over the entire session.

MeasurementObserved range
utilization_percent1.0 to 99.0
memory_used_mib5627.0 to 15585.0
power_w93.0 to 121.2
temperature_c49.0 to 52.0

The window contains 24 samples. Resource JSON log

Recorded robot results

The table is reporting measured runs. A missing sensor is staying visible as missing evidence. Force peaks are describing sampled interface contacts at the control rate. They are not certifying every 240 Hz physics substep or a calibrated hardware wrist sensor.

RunLast phaseFinal gap mmPeak axial NPull proof secondsFull simulation gateEvidence
assembly-seed200Pull test0.24019.8730.000NOT ACCEPTEDJSON record
assembly-seed201Safe stop0.40824.1000.000NOT ACCEPTEDJSON record
assembly-seed202Release-0.00028.7672.050PASSJSON record
assembly-seed203Release-0.00031.9522.050PASSJSON record
assembly-seed204Release-0.00037.4342.050PASSJSON record
assembly-seed205Pin insert-0.00047.4360.000NOT ACCEPTEDJSON record
assembly-seed206Release-0.00027.8702.050PASSJSON record
assembly-seed340Release-0.00032.5642.050PASSJSON record
assembly-seed341Release-0.00029.1922.050PASSJSON record
assembly-seed342Release-0.00029.7312.050PASSJSON record
assembly-seed343Release-0.00030.2382.050PASSJSON record
assembly-seed344Release-0.00037.7352.050PASSJSON record
assembly-seed345Safe stop50.3064.7440.000NOT ACCEPTEDJSON record
assembly-seed346Release-0.00036.9362.050PASSJSON record
assembly-seed347Release-0.00029.8342.050PASSJSON record
assembly-seed348Safe stop44.6339.4130.000NOT ACCEPTEDJSON record
assembly-seed400Release-0.00030.0802.050PASSJSON record
assembly-seed401Release-0.00040.3352.050PASSJSON record
assembly-seed402Release-0.00028.7722.050PASSJSON record
assembly-seed403Release-0.00030.0482.050PASSJSON record
cli-alignment345-v20Release-0.00029.9212.050PASSJSON record
cli-alignment348-v20Release-0.00034.2452.050PASSJSON record
cli-grasp-v17Release-0.00028.4282.050NOT ACCEPTEDJSON record
cli-grasp-v18Release-0.00028.5622.050PASSJSON record
cli-grasp-v19Release-0.00030.3912.050PASSJSON record
cli-grasp205-v21Release-0.00030.5492.050NOT ACCEPTEDJSON record
cli-grasp345-v21Release-0.00035.4602.050NOT ACCEPTEDJSON record
cli-grasp348-v21Release-0.00036.6792.050NOT ACCEPTEDJSON record
cli-grasp401-v21Release-0.00032.1342.050NOT ACCEPTEDJSON record
cli-hardened-v14Release-0.00033.0942.050PASSJSON record
cli-nominal-v10Safe stop53.93818.6470.000NOT ACCEPTEDJSON record
cli-recovery-v11Safe stop0.20417.2840.000NOT ACCEPTEDJSON record
cli-regression205-v16Safe stop0.09034.3231.650NOT ACCEPTEDJSON record
cli-regression205-v17Insert43.0993.7920.000NOT ACCEPTEDJSON record
cli-regression205-v18Safe stop0.05738.1070.250NOT ACCEPTEDJSON record
cli-regression205-v19Release-0.00037.1422.050PASSJSON record
cli-retry-v13Release-0.00033.0942.050PASSJSON record
cli-stabilized-v15Release-0.00036.6182.050PASSJSON record
feedback-v3Align50.996Not measured0.000NOT ACCEPTEDJSON record
feedback-v4Retract52.061Not measured0.000NOT ACCEPTEDJSON record
full-v9Safe stop0.15917.9420.000NOT ACCEPTEDJSON record
geometry-v2Approach38.233Not measured0.000NOT ACCEPTEDJSON record
pin-v6Safe stop1.922Not measured0.000NOT ACCEPTEDJSON record
pin-v7Safe stop-0.004Not measured0.000NOT ACCEPTEDJSON record
pin-v8Safe stop-0.002Not measured0.000NOT ACCEPTEDJSON record
pull-controller-probe-v12Safe stop-0.00028.0872.000NOT ACCEPTEDJSON record
pull-controller-probe-v13Release-0.00028.0872.000NOT ACCEPTEDJSON record
seating-v5Verify seating0.057Not measured0.000NOT ACCEPTEDJSON record

Randomized insertion repeatability

The frozen campaign is varying initial yaw from minus six to plus six degrees. It is varying approach offset within three millimeters. Friction is varying by twenty percent and mass by ten percent. The controller is receiving simulator pose feedback. This is testing physical insertion repeatability with privileged sensing.

The recorded result is 20 passes in 20 completed trials. The Wilson 95 percent interval is 0.839 to 1.000. A small campaign is not establishing a production failure rate.

SeedYaw degreesApproach offset mmFriction scaleMass scaleFinal gap mmPeak sampled contact NInsertion gate
100-3.48-1.720.961.090.0403.051PASS
1010.05-1.070.810.940.0362.855PASS
102-5.920.131.051.100.0271.966PASS
1030.03-1.531.011.010.0753.111PASS
1040.691.991.080.940.1035.276PASS
105-0.78-0.260.850.990.1442.447PASS
106-3.54-1.631.030.900.0153.543PASS
107-3.44-0.080.861.040.0152.190PASS
108-3.010.200.890.980.0164.016PASS
109-4.01-2.510.981.000.0173.053PASS
110-5.961.901.171.030.0092.226PASS
111-2.200.761.130.980.0115.455PASS
1123.12-0.211.160.920.1473.801PASS
113-1.371.421.050.950.1374.445PASS
1145.182.980.820.910.0911.964PASS
1152.91-2.810.811.090.1666.389PASS
116-2.231.191.090.970.0502.665PASS
1172.34-2.660.960.960.1462.714PASS
118-0.821.241.180.900.1473.501PASS
1191.14-2.961.171.100.0872.803PASS

Engineering findings and corrections

The initial GPU pilot is ending with zero task score. Inspection is identifying missing production sensor and action bindings in the original adapter. The original release checker is looking only at final safety values. It is also trusting a simulator name and supplied video metadata too broadly.

The revised scene is separating the housing grasp from the insertion point. This is reducing interference between the two robot grippers. The first seated approach is still showing about five millimeters of remaining gap. Geometry inspection is identifying a shoulder and rim mismatch. The corrected rim is allowing the intended 32 mm insertion depth without relaxing the depth threshold.

The physical cross pin is then entering the mating holes. The first pull attempt is exposing excessive mechanical play and fixture motion. The tighter pin is reducing available play but is demanding more accurate alignment. Full orientation feedback and measured tool offsets are addressing pin tilt. Active left arm feedback is reacting to fixture movement.

The software checks are now examining complete telemetry. They are rejecting nonfinite measurements and discontinuous steps. They are requiring continuous pull evidence. The development twin is rejecting motion proof before a sustained pull test. Its friction parameter is affecting contact behavior. Invalid work orders are failing validation.

The recording pipeline is saving lossless PNG frames with pixel hashes. H264 export is verifying decoded frame counts. Earlier raw NumPy frames are being removed only after successful video verification. Source snapshots are identifying the code used by each newer run. The earliest development runs are retaining their logs without retroactively claiming stronger source provenance.

Controller hardening and regression evidence

The updated left arm controller is tracking the measured grasp transform in the housing frame. It is following housing motion while retaining the original grasp reference. The pull controller is loading more slowly and is unloading faster when the measured load trend predicts an overshoot. The original force and grasp limits are remaining unchanged.

Every stop transition is preserving measured joint targets. Safety faults are taking priority over retry suggestions. The campaign runner is exporting three camera views for every rendered trial and is checking decoded frame counts before compacting disposable frames. It is terminating the full process group on timeout.

Software regression results

Alignment reachability analysis

Trial 345 is ending in a bounded alignment timeout. Its final right wrist joint is measuring -96.972 degrees against a lower limit of -97.000 degrees. An offline inverse kinematics sweep is evaluating lower alignment poses from that recorded state. The calculation is identifying candidate reachable targets. It is not establishing physical recovery success.

Alignment Height mmPosition Residual mmOrientation Residual DegreesWrist Joint Degrees
50.01.4410.401-97.000
45.00.0690.010-95.613
40.00.0730.011-93.766
35.00.0620.009-92.044
30.00.0490.007-90.426

Kinematics diagnostic JSON

Grasp motion failure analysis

The recorded failure is occurring during the pull proof. The displacement decomposition is separating lateral grasp motion from axial compliance. It is using the same original grasp reference as the acceptance audit.

Recorded RunPhaseX Motion mmY Motion mmZ Motion mmTotal Motion mmPull Load N
assembly-seed401Pull test-0.0012.0040.2772.02329.68
cli-alignment345-v20Insert-0.0531.6950.0011.6960.00
cli-alignment348-v20Pull test0.0181.5250.1951.53728.79

Measured displacement decomposition

Pull grasp regression evaluation

The candidate controller is retaining the observed gripper orientation relative to the module while applying the pull load. The evaluation is repeating the exact recorded yaw and friction and mass settings from four difficult cases. These targeted regressions are testing the correction and are not replacing the independent qualification campaign.

Recorded RunAssembly ChecksGrasp Proxy mmFinal Yaw DegreesProcess ExitFull Trial Gate
cli-grasp401-v21FAIL1.5767.358124FAIL
cli-grasp345-v21FAIL1.6967.2790FAIL
cli-grasp348-v21FAIL1.5047.2420FAIL
cli-grasp205-v21FAIL1.4667.3260FAIL

Regression measurements by run

What is still required before production release

The production release remains closed. Hardware production release is requiring calibrated physical validation in addition to the recorded simulation campaign.

The simulation acceptance contract is requiring at least twenty complete recovery trials with an observed acceptance rate of at least 95 percent. The current release table is reporting whether this gate is passing. It is requiring measured pull proof and jaw motion in each accepted run. It is requiring independent wrist wrench calibration and complete servo timing coverage. It is requiring collision and limit validation on the physical YAM hardware. It is requiring a cell specific inspection dataset and a documented process for handling uncertain or failed QA.

The public datasets are testing related capabilities. They are not representing this exact gripper interface. The image models are using a 256 by 256 input and may be losing very small defects. The current normal calibration threshold is favoring a low false alarm rate and is missing some anomalies. Those misses are remaining visible in the prediction files.

The interface wrench is coming from simulated contacts. It is not substituting for a calibrated six axis wrist sensor. The controller is depending on privileged simulator poses. A hardware release requires a validated perception and calibration path. An unattended production cell is also needing independent emergency stop behavior and a validated protective system.

Sources and reproducibility

The public image data is coming from MVTec AD and KolektorSDD2. The robot process data is coming from voraus AD. Dataset licensing is being assessed separately from model performance. Commercial deployment is requiring suitable data rights and cell specific validation.

Dataset URLs and archive hashes are appearing in the acquisition record. Each evaluation is retaining split membership and prediction records. Each recorded robot run is retaining telemetry and an independent assembly record. The final package is providing a SHA256 manifest so transferred files can be checked locally.

Recorded run: assembly-seed200

The run is ending in the Pull test phase. The independent verifier is reporting complete_assembly_sequence, sustained_pull, observed_motion, arms_released.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.150000000000038,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.150000000000237,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.150000000000293,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.15000000000031,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 39.449999999999896,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 41.49999999999978,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 53.74999999999908,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 57.749999999998856,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 77.34999999999775,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 79.39999999999763,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 86.14999999999725,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": false,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": false,
    "observed_motion": false,
    "arms_released": false
  }
}
Recorded run: assembly-seed201

The run is ending in the Safe stop phase. The independent verifier is reporting complete_assembly_sequence, sampled_force_limits, sustained_pull, observed_motion, arms_released.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.000000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.000000000000234,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.00000000000029,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.00000000000032,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 39.19999999999991,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 41.249999999999794,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 53.4999999999991,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 58.49999999999881,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 75.99999999999783,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 78.04999999999771,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 84.79999999999733,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 104.84999999999619,
      "phase": "safe_stop",
      "reason": "Pull proof timeout"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": false,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": false,
    "sampled_torque_limit": true,
    "sustained_pull": false,
    "observed_motion": false,
    "arms_released": false
  }
}
Recorded run: assembly-seed202

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.000000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.000000000000107,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.000000000000163,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 27.20000000000025,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 34.350000000000186,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 36.40000000000007,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 48.64999999999937,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 54.99999999999901,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 73.64999999999796,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 75.69999999999784,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 82.44999999999746,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 94.49999999999677,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 97.34999999999661,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 99.3999999999965,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: assembly-seed203

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.050000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.050000000000235,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.050000000000292,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.05000000000032,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 39.099999999999916,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 41.1499999999998,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 53.3999999999991,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 58.649999999998805,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 76.04999999999782,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 78.0999999999977,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 84.84999999999732,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 99.89999999999647,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 102.7499999999963,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 104.79999999999619,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: assembly-seed204

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.000000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.000000000000234,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.00000000000029,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.00000000000032,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 39.3499999999999,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 41.399999999999785,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 53.64999999999909,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 57.34999999999888,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 74.29999999999792,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 76.3499999999978,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 83.09999999999742,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 97.24999999999662,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 100.09999999999646,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 102.14999999999634,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: assembly-seed205

The run is ending in the Pin insert phase. The independent verifier is reporting complete_assembly_sequence, pin_engagement, sampled_force_limits, sustained_pull, observed_motion, arms_released.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.200000000000038,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.200000000000237,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.200000000000294,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 35.250000000000135,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 42.54999999999972,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 44.5999999999996,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 56.84999999999891,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 62.79999999999857,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 81.44999999999752,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 83.4999999999974,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 90.24999999999702,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 94.84999999999675,
      "phase": "retract",
      "reason": "Measured contact force exceeds 45 N"
    },
    {
      "time_s": 98.89999999999652,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 104.44999999999621,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 104.4999999999962,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 106.54999999999609,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 118.79999999999539,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 131.34999999999562,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": false,
    "seating": true,
    "pin_engagement": false,
    "sampled_force_limits": false,
    "sampled_torque_limit": true,
    "sustained_pull": false,
    "observed_motion": false,
    "arms_released": false
  }
}
Recorded run: assembly-seed206

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.200000000000038,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.200000000000237,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.200000000000294,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.20000000000031,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 39.24999999999991,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 41.29999999999979,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 53.549999999999095,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 58.7499999999988,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 77.39999999999775,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 79.44999999999763,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 86.19999999999725,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 97.34999999999661,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 100.19999999999645,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 102.24999999999633,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: assembly-seed340

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.450000000000042,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.45000000000024,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.450000000000298,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.50000000000029,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 39.74999999999988,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 41.79999999999976,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 54.049999999999066,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 57.049999999998896,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 73.19999999999798,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 75.24999999999787,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 81.99999999999748,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 95.19999999999673,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 98.04999999999657,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 100.09999999999646,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: assembly-seed341

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.400000000000041,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.400000000000112,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.40000000000017,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 28.40000000000027,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 35.9000000000001,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 37.94999999999998,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 50.199999999999285,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 56.59999999999892,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 73.79999999999795,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 75.84999999999783,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 82.59999999999745,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 94.1499999999968,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 96.99999999999663,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 99.04999999999652,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: assembly-seed342

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 13.00000000000005,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 27.00000000000025,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 31.000000000000306,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 33.300000000000246,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 40.39999999999984,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 42.449999999999726,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 54.69999999999903,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 58.7499999999988,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 77.69999999999773,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 79.74999999999761,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 86.49999999999723,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 98.34999999999656,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 101.1999999999964,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 103.24999999999628,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: assembly-seed343

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.250000000000039,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.250000000000238,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.250000000000295,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.250000000000306,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 39.24999999999991,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 41.29999999999979,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 53.549999999999095,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 58.84999999999879,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 77.29999999999775,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 79.34999999999764,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 86.09999999999725,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 97.99999999999658,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 100.84999999999641,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 102.8999999999963,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: assembly-seed344

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.100000000000037,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.100000000000108,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.100000000000165,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 27.75000000000026,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 34.80000000000016,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 36.850000000000044,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 49.09999999999935,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 54.049999999999066,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 72.44999999999803,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 74.49999999999791,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 81.24999999999753,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 100.69999999999642,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 103.54999999999626,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 105.59999999999614,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: assembly-seed345

The run is ending in the Safe stop phase. The independent verifier is reporting complete_assembly_sequence, seating, pin_engagement, sustained_pull, observed_motion, arms_released.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.150000000000038,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.150000000000237,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.150000000000293,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 50.199999999999285,
      "phase": "safe_stop",
      "reason": "Alignment timeout"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": false,
    "seating": false,
    "pin_engagement": false,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": false,
    "observed_motion": false,
    "arms_released": false
  }
}
Recorded run: assembly-seed346

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.30000000000004,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.30000000000024,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.300000000000296,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.65000000000028,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 39.94999999999987,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 41.99999999999975,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 54.249999999999055,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 58.299999999998825,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 77.14999999999776,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 79.19999999999764,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 85.94999999999726,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 103.89999999999624,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 106.74999999999608,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 108.79999999999596,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: assembly-seed347

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.250000000000039,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.250000000000238,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.250000000000295,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.250000000000306,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 39.299999999999905,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 41.34999999999979,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 53.59999999999909,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 60.049999999998725,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 78.94999999999766,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 80.99999999999754,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 87.74999999999716,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 99.49999999999649,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 102.34999999999633,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 104.39999999999621,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: assembly-seed348

The run is ending in the Safe stop phase. The independent verifier is reporting complete_assembly_sequence, seating, pin_engagement, sustained_pull, observed_motion, arms_released.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.000000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.000000000000107,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.000000000000163,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 41.049999999999805,
      "phase": "safe_stop",
      "reason": "Alignment timeout"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": false,
    "seating": false,
    "pin_engagement": false,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": false,
    "observed_motion": false,
    "arms_released": false
  }
}
Recorded run: assembly-seed400

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.200000000000038,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.200000000000237,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.200000000000294,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.20000000000031,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 38.79999999999993,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 40.84999999999982,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 53.09999999999912,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 57.84999999999885,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 74.54999999999791,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 76.59999999999779,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 83.34999999999741,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 94.99999999999675,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 97.84999999999658,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 99.89999999999647,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: assembly-seed401

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.000000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.000000000000234,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.00000000000029,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.65000000000028,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 39.14999999999991,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 41.1999999999998,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 53.4499999999991,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 56.9499999999989,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 73.59999999999796,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 75.64999999999785,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 82.39999999999746,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 101.59999999999637,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 104.44999999999621,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 106.49999999999609,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: assembly-seed402

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.000000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.000000000000107,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.000000000000163,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 24.95000000000022,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 31.600000000000314,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 33.650000000000226,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 45.89999999999953,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 50.69999999999926,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 69.09999999999822,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 71.1499999999981,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 77.89999999999772,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 89.04999999999708,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 91.89999999999692,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 93.9499999999968,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: assembly-seed403

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.050000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.050000000000107,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.050000000000164,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 25.850000000000232,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 32.15000000000031,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 34.200000000000195,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 46.4499999999995,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 52.999999999999126,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 71.69999999999807,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 73.74999999999795,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 80.49999999999757,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 91.74999999999693,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 94.59999999999677,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 96.64999999999665,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: cli-alignment345-v20

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

The composite is showing three recorded cameras with measured telemetry labels. The original uninterrupted camera recording is following below.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.150000000000038,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.150000000000237,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.150000000000293,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.3000000000003,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 38.79999999999993,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 40.84999999999982,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 53.09999999999912,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 56.84999999999891,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 73.74999999999795,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 75.79999999999784,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 82.54999999999745,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 95.29999999999673,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 98.14999999999657,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 100.19999999999645,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: cli-alignment348-v20

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

The composite is showing three recorded cameras with measured telemetry labels. The original uninterrupted camera recording is following below.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.000000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.000000000000107,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.000000000000163,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 23.050000000000193,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 29.80000000000029,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 31.800000000000317,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 44.049999999999635,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 50.24999999999928,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 69.09999999999822,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 71.1499999999981,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 77.89999999999772,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 94.74999999999676,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 97.5999999999966,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 99.64999999999648,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: cli-grasp-v17

The run is ending in the Release phase. The independent verifier is reporting seating.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.050000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.050000000000107,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.050000000000164,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 26.000000000000234,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 33.20000000000025,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 35.250000000000135,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 47.49999999999944,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 54.49999999999904,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 72.849999999998,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 74.89999999999789,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 81.6499999999975,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 94.69999999999676,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 97.5499999999966,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 99.59999999999648,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": false,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: cli-grasp-v18

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.050000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.050000000000107,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.050000000000164,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 26.000000000000234,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 33.20000000000025,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 35.250000000000135,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 47.49999999999944,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 54.49999999999904,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 72.849999999998,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 74.89999999999789,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 81.6499999999975,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 96.59999999999665,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 99.44999999999649,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 101.49999999999638,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: cli-grasp-v19

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.050000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.050000000000107,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.050000000000164,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 26.000000000000234,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 33.20000000000025,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 35.250000000000135,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 47.49999999999944,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 54.49999999999904,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 72.849999999998,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 74.89999999999789,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 81.6499999999975,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 93.59999999999683,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 96.44999999999666,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 98.49999999999655,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: cli-grasp205-v21

The run is ending in the Release phase. The independent verifier is reporting seating.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.250000000000039,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.250000000000238,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.250000000000295,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.50000000000029,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 39.099999999999916,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 41.1499999999998,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 53.3999999999991,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 57.44999999999887,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 76.09999999999782,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 78.1499999999977,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 84.89999999999732,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 97.79999999999659,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 100.64999999999642,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 102.69999999999631,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": false,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: cli-grasp345-v21

The run is ending in the Release phase. The independent verifier is reporting seating.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.150000000000038,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.150000000000237,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.150000000000293,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.3000000000003,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 38.79999999999993,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 40.84999999999982,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 53.09999999999912,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 56.84999999999891,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 73.74999999999795,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 75.79999999999784,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 82.54999999999745,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 98.64999999999654,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 101.49999999999638,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 103.54999999999626,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": false,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: cli-grasp348-v21

The run is ending in the Release phase. The independent verifier is reporting seating.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.000000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.000000000000107,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.000000000000163,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 23.050000000000193,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 29.80000000000029,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 31.800000000000317,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 44.049999999999635,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 50.24999999999928,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 69.09999999999822,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 71.1499999999981,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 77.89999999999772,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 96.69999999999665,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 99.54999999999649,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 101.59999999999637,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": false,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: cli-grasp401-v21

The run is ending in the Release phase. The independent verifier is reporting seating.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.000000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.000000000000234,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.00000000000029,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 32.65000000000028,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 39.14999999999991,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 41.1999999999998,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 53.4499999999991,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 56.9499999999989,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 73.59999999999796,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 75.64999999999785,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 82.39999999999746,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 96.19999999999668,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 99.04999999999652,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 101.0999999999964,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": false,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: cli-hardened-v14

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

The composite is showing three recorded cameras with measured telemetry labels. The original uninterrupted camera recording is following below.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.000000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.000000000000107,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.000000000000163,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 26.100000000000236,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 33.300000000000246,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 35.35000000000013,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 47.59999999999943,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 55.149999999999004,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 73.54999999999797,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 75.59999999999785,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 82.34999999999746,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 96.84999999999664,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 99.69999999999648,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 101.74999999999636,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: cli-nominal-v10

The run is ending in the Safe stop phase. The independent verifier is reporting complete_assembly_sequence, seating, pin_engagement, sustained_pull, observed_motion, arms_released.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.000000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.050000000000107,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.050000000000164,
      "phase": "safe_stop",
      "reason": "Bounded recovery budget check"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": false,
    "seating": false,
    "pin_engagement": false,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": false,
    "observed_motion": false,
    "arms_released": false
  }
}
Recorded run: cli-recovery-v11

The run is ending in the Safe stop phase. The independent verifier is reporting complete_assembly_sequence, sampled_force_limits, sustained_pull, observed_motion, arms_released.

The composite is showing three recorded cameras with measured telemetry labels. The original uninterrupted camera recording is following below.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.000000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.000000000000107,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.000000000000163,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 26.100000000000236,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 33.300000000000246,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 35.35000000000013,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 47.59999999999943,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 55.149999999999004,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 73.54999999999797,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 75.59999999999785,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 82.34999999999746,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 102.39999999999633,
      "phase": "safe_stop",
      "reason": "Pull proof timeout"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": false,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": false,
    "sampled_torque_limit": true,
    "sustained_pull": false,
    "observed_motion": false,
    "arms_released": false
  }
}
Recorded run: cli-regression205-v16

The run is ending in the Safe stop phase. The independent verifier is reporting complete_assembly_sequence, sustained_pull, observed_motion, arms_released.

The composite is showing three recorded cameras with measured telemetry labels. The original uninterrupted camera recording is following below.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.250000000000039,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.250000000000238,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.250000000000295,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 34.60000000000017,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 41.79999999999976,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 43.849999999999646,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 56.09999999999895,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 61.69999999999863,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 78.99999999999766,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 81.04999999999754,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 87.79999999999715,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 117.84999999999545,
      "phase": "safe_stop",
      "reason": "Pull proof timeout"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": false,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": false,
    "observed_motion": false,
    "arms_released": false
  }
}
Recorded run: cli-regression205-v17

The run is ending in the Insert phase. The independent verifier is reporting complete_assembly_sequence, seating, pin_engagement, sustained_pull, observed_motion, arms_released.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.250000000000039,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.250000000000238,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.250000000000295,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 34.60000000000017,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": false,
    "seating": false,
    "pin_engagement": false,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": false,
    "observed_motion": false,
    "arms_released": false
  }
}
Recorded run: cli-regression205-v18

The run is ending in the Safe stop phase. The independent verifier is reporting complete_assembly_sequence, sustained_pull, observed_motion, arms_released.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.250000000000039,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.250000000000238,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.250000000000295,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 34.60000000000017,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 41.79999999999976,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 43.849999999999646,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 56.09999999999895,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 61.69999999999863,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 78.99999999999766,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 81.04999999999754,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 87.79999999999715,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 117.84999999999545,
      "phase": "safe_stop",
      "reason": "Pull proof timeout"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": false,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": false,
    "observed_motion": false,
    "arms_released": false
  }
}
Recorded run: cli-regression205-v19

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

The composite is showing three recorded cameras with measured telemetry labels. The original uninterrupted camera recording is following below.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.250000000000039,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.250000000000238,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.250000000000295,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 34.60000000000017,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 41.79999999999976,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 43.849999999999646,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 56.09999999999895,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 61.69999999999863,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 78.99999999999766,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 81.04999999999754,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 87.79999999999715,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 104.74999999999619,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 107.59999999999603,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 109.64999999999591,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: cli-retry-v13

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

The composite is showing three recorded cameras with measured telemetry labels. The original uninterrupted camera recording is following below.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.000000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.000000000000107,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.000000000000163,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 26.100000000000236,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 33.300000000000246,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 35.35000000000013,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 47.59999999999943,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 55.149999999999004,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 73.54999999999797,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 75.59999999999785,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 82.34999999999746,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 96.84999999999664,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 99.69999999999648,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 101.74999999999636,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: cli-stabilized-v15

The run is ending in the Release phase. The independent verifier is reporting all implemented task checks passed.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.050000000000036,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 17.050000000000107,
      "phase": "retract",
      "reason": "Loaded insertion is showing less than 0.5 mm progress in one second"
    },
    {
      "time_s": 21.050000000000164,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 26.000000000000234,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 33.20000000000025,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 35.250000000000135,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 47.49999999999944,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 54.49999999999904,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 72.849999999998,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 74.89999999999789,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 81.6499999999975,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 100.09999999999646,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 102.9499999999963,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 104.99999999999618,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": true,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: feedback-v3

The run is ending in the Align phase. The independent verifier is reporting telemetry_finite, telemetry_contiguous, contact_force_available, contact_torque_available, complete_assembly_sequence, seating, pin_engagement, sampled_force_limits, sampled_torque_limit, sustained_pull, observed_motion, arms_released.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    }
  ],
  "checks": {
    "telemetry_finite": false,
    "telemetry_contiguous": false,
    "contact_force_available": false,
    "contact_torque_available": false,
    "no_sensor_errors": true,
    "complete_assembly_sequence": false,
    "seating": false,
    "pin_engagement": false,
    "sampled_force_limits": false,
    "sampled_torque_limit": false,
    "sustained_pull": false,
    "observed_motion": false,
    "arms_released": false
  }
}
Recorded run: feedback-v4

The run is ending in the Retract phase. The independent verifier is reporting telemetry_finite, telemetry_contiguous, contact_force_available, contact_torque_available, complete_assembly_sequence, seating, pin_engagement, sampled_force_limits, sampled_torque_limit, sustained_pull, observed_motion, arms_released.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.950000000000049,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 26.950000000000248,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 30.950000000000305,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 33.150000000000254,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 47.199999999999456,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    },
    {
      "time_s": 51.249999999999226,
      "phase": "align",
      "reason": "Bounded recovery budget check"
    },
    {
      "time_s": 53.349999999999106,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 67.39999999999831,
      "phase": "retract",
      "reason": "Insertion timeout with unresolved gap"
    }
  ],
  "checks": {
    "telemetry_finite": false,
    "telemetry_contiguous": false,
    "contact_force_available": false,
    "contact_torque_available": false,
    "no_sensor_errors": true,
    "complete_assembly_sequence": false,
    "seating": false,
    "pin_engagement": false,
    "sampled_force_limits": false,
    "sampled_torque_limit": false,
    "sustained_pull": false,
    "observed_motion": false,
    "arms_released": false
  }
}
Recorded run: full-v9

The run is ending in the Safe stop phase. The independent verifier is reporting contact_torque_available, complete_assembly_sequence, sampled_torque_limit, sustained_pull, observed_motion, arms_released.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.100000000000037,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 19.200000000000138,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 21.200000000000166,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 33.40000000000024,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 37.40000000000001,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 55.74999999999897,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 57.79999999999885,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 64.54999999999848,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 84.59999999999734,
      "phase": "safe_stop",
      "reason": "Pull proof timeout"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": false,
    "no_sensor_errors": true,
    "complete_assembly_sequence": false,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": false,
    "sustained_pull": false,
    "observed_motion": false,
    "arms_released": false
  }
}
Recorded run: geometry-v2

The run is ending in the Approach phase. The independent verifier is reporting telemetry_finite, telemetry_contiguous, contact_force_available, contact_torque_available, no_sensor_errors, complete_assembly_sequence, seating, pin_engagement, sampled_force_limits, sampled_torque_limit, sustained_pull, observed_motion, arms_released.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [],
  "checks": {
    "telemetry_finite": false,
    "telemetry_contiguous": false,
    "contact_force_available": false,
    "contact_torque_available": false,
    "no_sensor_errors": false,
    "complete_assembly_sequence": false,
    "seating": false,
    "pin_engagement": false,
    "sampled_force_limits": false,
    "sampled_torque_limit": false,
    "sustained_pull": false,
    "observed_motion": false,
    "arms_released": false
  }
}
Recorded run: pin-v6

The run is ending in the Safe stop phase. The independent verifier is reporting telemetry_finite, telemetry_contiguous, contact_force_available, contact_torque_available, complete_assembly_sequence, seating, sampled_force_limits, sampled_torque_limit, sustained_pull, observed_motion, arms_released.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 12.950000000000049,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 20.200000000000152,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 22.20000000000018,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 34.40000000000018,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 36.45000000000007,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 47.44999999999944,
      "phase": "verify_pin",
      "reason": "Measured cross pin position is within tolerance"
    },
    {
      "time_s": 49.499999999999325,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 56.24999999999894,
      "phase": "pull_test",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 76.29999999999781,
      "phase": "safe_stop",
      "reason": "Pull proof timeout"
    }
  ],
  "checks": {
    "telemetry_finite": false,
    "telemetry_contiguous": false,
    "contact_force_available": false,
    "contact_torque_available": false,
    "no_sensor_errors": true,
    "complete_assembly_sequence": false,
    "seating": false,
    "pin_engagement": true,
    "sampled_force_limits": false,
    "sampled_torque_limit": false,
    "sustained_pull": false,
    "observed_motion": false,
    "arms_released": false
  }
}
Recorded run: pin-v7

The run is ending in the Safe stop phase. The independent verifier is reporting telemetry_finite, telemetry_contiguous, contact_force_available, contact_torque_available, complete_assembly_sequence, seating, pin_engagement, sampled_force_limits, sampled_torque_limit, sustained_pull, observed_motion, arms_released.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 13.00000000000005,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 20.250000000000153,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 22.25000000000018,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 34.45000000000018,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 36.500000000000064,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 56.549999999998924,
      "phase": "safe_stop",
      "reason": "Physical retaining pin did not seat"
    }
  ],
  "checks": {
    "telemetry_finite": false,
    "telemetry_contiguous": false,
    "contact_force_available": false,
    "contact_torque_available": false,
    "no_sensor_errors": true,
    "complete_assembly_sequence": false,
    "seating": false,
    "pin_engagement": false,
    "sampled_force_limits": false,
    "sampled_torque_limit": false,
    "sustained_pull": false,
    "observed_motion": false,
    "arms_released": false
  }
}
Recorded run: pin-v8

The run is ending in the Safe stop phase. The independent verifier is reporting telemetry_finite, telemetry_contiguous, contact_force_available, contact_torque_available, complete_assembly_sequence, seating, pin_engagement, sampled_force_limits, sampled_torque_limit, sustained_pull, observed_motion, arms_released.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 13.00000000000005,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 20.15000000000015,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    },
    {
      "time_s": 22.15000000000018,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 34.350000000000186,
      "phase": "pin_align",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 36.80000000000005,
      "phase": "pin_insert",
      "reason": "Physical pin is aligned with cross holes"
    },
    {
      "time_s": 56.84999999999891,
      "phase": "safe_stop",
      "reason": "Physical retaining pin did not seat"
    }
  ],
  "checks": {
    "telemetry_finite": false,
    "telemetry_contiguous": false,
    "contact_force_available": false,
    "contact_torque_available": false,
    "no_sensor_errors": true,
    "complete_assembly_sequence": false,
    "seating": false,
    "pin_engagement": false,
    "sampled_force_limits": false,
    "sampled_torque_limit": false,
    "sustained_pull": false,
    "observed_motion": false,
    "arms_released": false
  }
}
Recorded run: pull-controller-probe-v12

The run is ending in the Safe stop phase. The independent verifier is reporting complete_assembly_sequence, observed_motion, arms_released.

This is an isolated controller experiment. The initial scene is already containing the module and retaining pin in their assembled positions. It is testing pull control and is not demonstrating installation or counting toward complete assembly success.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "pull_test",
      "reason": "Grasp completed"
    },
    {
      "time_s": 21.150000000000166,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 23.950000000000205,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 31.95000000000032,
      "phase": "safe_stop",
      "reason": "Gripper motion did not reach commanded angle"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": false,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": false,
    "arms_released": false
  }
}
Recorded run: pull-controller-probe-v13

The run is ending in the Release phase. The independent verifier is reporting complete_assembly_sequence.

This is an isolated controller experiment. The initial scene is already containing the module and retaining pin in their assembled positions. It is testing pull control and is not demonstrating installation or counting toward complete assembly success.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "pull_test",
      "reason": "Grasp completed"
    },
    {
      "time_s": 21.150000000000166,
      "phase": "transfer",
      "reason": "Executing bounded collision clearance waypoints"
    },
    {
      "time_s": 23.950000000000205,
      "phase": "motion_open",
      "reason": "Waypoint transfer completed"
    },
    {
      "time_s": 25.950000000000234,
      "phase": "motion_close",
      "reason": "Measured gripper joint travel is reaching 30 degrees"
    }
  ],
  "checks": {
    "telemetry_finite": true,
    "telemetry_contiguous": true,
    "contact_force_available": true,
    "contact_torque_available": true,
    "no_sensor_errors": true,
    "complete_assembly_sequence": false,
    "seating": true,
    "pin_engagement": true,
    "sampled_force_limits": true,
    "sampled_torque_limit": true,
    "sustained_pull": true,
    "observed_motion": true,
    "arms_released": true
  }
}
Recorded run: seating-v5

The run is ending in the Verify seating phase. The independent verifier is reporting telemetry_finite, telemetry_contiguous, contact_force_available, contact_torque_available, complete_assembly_sequence, pin_engagement, sampled_force_limits, sampled_torque_limit, sustained_pull, observed_motion, arms_released.

This recording is showing the actual bimanual YAM scene. It is retaining the full recorded sequence. Playback is using the recorded 20 Hz control rate.

Measured geometry and force traces
The vertical markers are identifying recorded controller transitions. Missing force measurements are remaining gaps in the plot.
Controller events and independent acceptance checks
{
  "events": [
    {
      "time_s": 10.000000000000007,
      "phase": "align",
      "reason": "Transport completed. Using measured relative pose."
    },
    {
      "time_s": 13.00000000000005,
      "phase": "insert",
      "reason": "Measured alignment is within 1 mm and 1 degree"
    },
    {
      "time_s": 20.300000000000153,
      "phase": "verify_seating",
      "reason": "Measured seating geometry is within tolerance"
    }
  ],
  "checks": {
    "telemetry_finite": false,
    "telemetry_contiguous": false,
    "contact_force_available": false,
    "contact_torque_available": false,
    "no_sensor_errors": true,
    "complete_assembly_sequence": false,
    "seating": true,
    "pin_engagement": false,
    "sampled_force_limits": false,
    "sampled_torque_limit": false,
    "sustained_pull": false,
    "observed_motion": false,
    "arms_released": false
  }
}

A recorded safety failure is driving the final correction

Randomized trial assembly-seed205 is recording 47.44 N of pull load against the 45 N axial limit. The older controller is entering a generic retraction path. The trial is being retained as a failed attempt and is being terminated after the violation.

The hardened controller is stopping on missing wrench data and on axial force or lateral force or torque violations. The software replay is feeding the exact recorded failure observation into that guard. It is requesting a stop while preserving measured joint targets. This is a software decision replay and is not claiming a new physics episode or a hardware emergency stop test.

{
  "phase": "safe_stop",
  "request_stop": true,
  "reason": "Axial interface force exceeds 45 N"
}

Recorded input and replay decision

Repeated seeds are exposing sensitivity

The MVTec experiment is covering the metal nut category only. It is not reporting an aggregate over the entire MVTec AD benchmark. The repeated runs are sharing the official image test sets while varying normal fitting and calibration membership. Their scores are therefore correlated. The table is showing observed ranges rather than treating seeds as independent production trials.

DatasetRunsAUROC rangeRecall rangeMissed anomaly range
ksdd250.926 to 0.9360.664 to 0.70033 to 37
mvtec-metal-nut50.973 to 0.9770.903 to 0.9356 to 9
voraus-ad50.980 to 0.9910.486 to 0.734201 to 388